Showing 1–9 of 64 results
-
BrassCraft 1/2 in. MIP x 1/2 in. MIP x 48 in. Gas Connector (1/2 in. OD) w/Safety+Plus2 Thermal Excess Flow Valve (60,500 BTU)
$27.27 $15.00BrassCrafts Safety+PLUS2 gas connector combines patented excess flow technology and thermal heat activation with the advanced corrosion resistance, to provide a safer gas connector for your home and family. In the event of a gas line rupture or disconnect, the excess flow valve (EFV) restricts gas flow at the appliance to a non-hazardous level. This immediate action helps avert the potential for a dangerous release of gas into the home. Gas is controlled only at the point where the problem exists; the rest of your system will continue to function. Safety+PLUS EFV automatically resets once the gas line is properly repaired. The thermal component utilizes a thermal ring that will restrict the flow through the valve when the valve is exposed to temperatures of 400F or more. BrassCraft’s stainless steel gas connector also features a proprietary polymer coating designed to withstand prolonged exposure to harsh household cleaning, plumbing repair and masonry products as well as UV rays and salt. Unlike conventional dipped or sprayed coatings, the ProCoat coating is baked directly on the connector surface at high temperatures to provide a uniform coating over the entire length of the connector. The coating is applied only after the connector has been 100% leak tested to provide complete corrosion resistance.
Every item checked for quality -
Everbilt 40/60 Pressure Switch for Well Pumps
$27.80 $15.29This pressure switch signals the pump to start when the water system drops to 40 psi (factory set) and stops at 60 psi (factory set). This switch is to be used with submersible well or jet pumps. It can be wired 115-Volt or 230-Volt. This switch must be used in conjunction with a well pressure tank. The air pressure in the well tank, when empty of all water, must be set to 38 psi or the switch will not operate properly.
- Turns pump on at 40 psi, off at 60 psi.
- Cap removes for easy adjustment.
- Can be wired 115-Volt or 230-Volt.
- For use with submersible well or jet pumps.
- Motor wires are connected to the 2 middle posts (color does not matter).
- Breaker box wires are connected to 2 outside posts (color does not matter).
- 2-spring design allows for adjustment of cut-in and cut-out pressure settings.
- Adjustments to springs should only be made by users with good knowledge of well systems.
Every item checked for quality -
SharkBite 1/2 in. Brass Push-to-Connect Dishwasher Installation Kit
$36.36 $20.00The SharkBite Dishwasher Installation Kit has everything you need to install your new dishwasher, it’s fast and simple. Push-to-Connect fittings require no glue, soldering, unions or tools. The kit includes 1 SharkBite 1/2 in. Dual Outlet Angle Stop Valve, 1 SharkBite 1/4 in. x 3/4 in. MPT Elbow, 1 SharkBite 1/4 in. x 3/4 in. GHT Elbow, 1 SharkBite 1/4 in. Stop Valve Adapter, 10 ft. coil of 1/4 in. PEX Pipe, 2 Disconnect Clips (1/2 in. and 1/4 in.). The SharkBite Dual Outlet Angle Stop Valves work with copper, PEX or CPVC. Just insert the pipe and the stainless steel teeth bite down and grip tight, while a specially formulated O-ring compresses to create a perfect seal. Disassembly is just as fast using the simple disconnect tool so fittings and valves can be easily changed and reused. They can even be rotated after assembly for easier installation in tight spaces. The included PEX coils can be cut to the exact length needed so there is no excess supply line to coil up behind the dishwasher.
- Lead free DZR brass construction for durability and reliability.
- Use to connect to any combination of copper, PEX, CPVC or PE-RT pipes.
- Innovative push-to-connect design makes for quick and easy installation.
- Push-to-connect fittings require no solder, glue, unions, or tools.
- Fitting can be rotated on pipe after installation making it easier to work in tight spaces.
- Designed for potable water distribution as well as hydronic heating applications.
- Corrosion resistant to improve longevity.
- Certified as a manufactured joint and for underground and behind-the-wall applications without access panels.
- Meets all UPC, IPC and cUPC requirements.
- Demount clip allows user to release the fitting from the pipe for convenient installation flexibility.
- Rated to 200°F and 200 psi.
- Rated to 200°F and 200 psi.
Every item checked for quality -
Apollo 3/4 In. X 3/4 In. Pvc Schedule 40 Slip X Slip Ball Valve Pro Pack (12-Pack)
$18.18 $10.00PVC Sch. 40 Ball Valves are compact and lightweight. This Slip x Slip valve is designed for a variety of applications including pressure distribution of cold water in irrigation, pool, spa, agricultural, commercial and light industrial applications and comes in a plastic jar of 12 valves which is convenient, resealable, and reusable. The ball valves are NSF approved and have EPDM seats and O-rings integrated into the durable PVC body.
- PVC schedule 40 construction for durability.
- Full port design allows for maximum efficiency and minimal turbulence or pressure reduction.
- Quarter-turn flow control for easy on and off.
- NSF / ANSI standard 372 certified.
- Slip connections conform to ASTM D2467.
- Working temperature range: 41°F to 122°F (5°C to 55°C).
- Maximum pressure rating 150 psi at 73°F (22°C).
- Requires solvent cement for installation (not included).
- Please note – as temperature increases, working pressure decreases, the optimal working pressure for PVC valves is 150 psi at 73°F (22°C) if the temperature increases above 73°F (22°C), use the PVC. correction factor to determine working pressure, multiply the maximum working pressure by the correction factor, please see correction factor grid on the attached specification sheet.
Every item checked for quality -
Apollo 1 in. PEX-A Expansion Sleeve/Ring (25-Pack)
$16.38 $9.01The Apollo ExpansionPEX 1 in. PEX-A Expansion Sleeve (25-Pack) is simple to install. Apollo ExpansionPEX are produced using PEX-A material. Apollo ExpansionPEX are required to create a secure Apollo ExpansionPEX connection. Apollo ExpansionPEX Expansion Sleeves are engineered with a bevel along the leading edge to ease pipe insertion and an integrated stop to ensure proper placement of the sleeve. The Apollo ExpansionPEX system is a comprehensive cold expansion piping system comprised of brass fittings, poly alloy fittings, manifolds, valves, fasteners, tools and tubing designed for implementation in water delivery systems, simple or complex.
- Designed for use with Apollo ExpansionPEX fittings and pipe and is compatible with all expansion type (ASTM F1960) systems.
- Designed for use with 1 in. PEX-A pipe and 1 in. PEX-A barb fittings.
- Pro pack includes 25 sleeves.
- Requires expansion tool (sold separately) for use.
- For use exclusively with PEX-A (ASTM F1960) pipe and systems.
- Meets or exceeds ASTM F1960 and ASTM F877 standards.
- Meets UPC, IPC and cUPC standard.
- Rated to 200F and 200 psi.
Every item checked for quality -
Pfister S60-151A 2-3/4 in. Zinc Die-Cast Crown Imperial Shower Flange with Sleeve in Chrome
$35.42 $19.48Flanges provides a decorative way to cover the stems of a faucet. S60-151A Crown Imperial Shower Flange is for use with new style Pfister shower valves. 2-piece design for easier installation.
- 2-3/4 in. O.D.
- Chrome finish.
- Includes set screw.
- Tube and flange design.
- Genuine Pfister replacement part.
- Internal threads to mount to stem.
Every item checked for quality -
BrassCraft 1/2 in. Nominal Push Connect x 1/2 in. FIP x 20 in. SpeediOne Braided Faucet Connector and 1/4-Turn Straight Valve
$3.64 $2.00Original Retail Price: $17.75.
BrassCraft’s push connect one-piece water supply combines their trusted brass water valve with their flexible braided polymer connector for one quick easy-to-install solution. BrassCraft’s one-piece connection features push connect technology on the valve inlet and a hand-tighten wing nut on the outlet to provide a significant savings in installation time and cost. Push connect valve inlet requires no special tools to install and comes equipped with a pre-inserted tube stiffener to make the product ideal for copper, PEX and CPVC piping systems. The braided polymer fibers of the connector are designed to bend freely without kinking or crimping in tight quarters and resist corrosion caused by chemicals found in common household, tile and glass cleaners. In addition, its reinforced inner hose resists corrosion under harsh water conditions.
- 1-piece unit combines valve and supply line.
- Saves time with one less connection.
- No special installation tools required.
- Installation ready with pre-inserted tube stiffener.
- Fast, reliable and secure.
- Compatible with copper, PEX and CPVC.
- Remove with combination removal tool or 5/8 in. open end wrench.
- Connector bends freely without kinking or crimping in tight quarters.
- No-lead certified.
- IAPMO and CSA listed to ASME A112.18.1/CSA B125.1.
Every item checked for quality -
Split Basin Faucet with Drain Stopper in Matte Black
$136.36 $75.00This KES bathroom sink faucet is NSF and cUPC certified, compliant with no-lead requirements and California (CEC) Standards. In addition, this KES matte black bathroom faucet is made with no-lead 18/8 stainless steel for safe drinking water. Water safety is our priority! This bathroom faucet also features a high-quality finish passing a rigorous salt spray test for superior corrosion resistance, rustproof and scratch resistance.
Every item checked for quality -
#2, STRM005CR, Chrome Single Lever Pull-Down Kitchen Faucet
$100.00 $55.00- Model: Star Mini Pull-Out Kitchen Mixer – STRM005CR.
- Function: Single Lever Pull-Down Kitchen Mixer/Faucet.
- Configuration: Single-Hole Installation.
- Finish: Chrome.
- Brand: Modern National.
- Manufacturer: Enping MN Kitchen & Bathroom Co., Ltd.
- Installation Instructions are Included.
Every item checked for quality
