Showing 154–162 of 260 results
-
SharkBite Push-to-Connect Faucet Installation Kit
$36.36 $20.00The SharkBite Faucet Installation Kit has everything you need to install your new faucet. The kit includes 2 SharkBite 1/2 in. x 1/4 in. (3/8 in. O.D.) Push-to-Connect Angle Stop Valves, two 5 ft. coils of 1/4 in. PEX Pipe, two 1/4 in. (3/8 in. O.D.) SharkBite x 1/2 in. Swivel Faucet Connectors, and a 1/2 in. Chrome Trim Cover reversed functions as a disconnect and 1/4 in. disconnect clip to remove the pipe from the fitting if needed. The SharkBite Angle Stop Valves work with copper, PEX or CPVC. Just insert the pipe and the stainless steel teeth bite down and grip tight, while a specially formulated O-ring compresses to create a perfect seal. Disassembly is just as fast using the simple disconnect tool so fittings and valves can be easily changed and reused. They can even be rotated after assembly for easier installation in tight spaces. The included PEX coils can be cut to the exact length needed so there is no excess supply line to coil up under the sink providing a clean, tangle free look. Once the stop valves are installed, thread the 1/2 in. faucet connectors onto the faucet connections and then measure and cut the PEX and push into the outlet on the stop valve and the faucet connector and the installation is complete.
Every item checked for quality -
Wilkins 3/4 in. Lead Free Brass NPT Pressure Relief Valve
$37.40 $20.57The P1000AXL-150C Pressure Relief Valve is set at 150 psi and utilized on water heating storage vessels for protection against over-temperature or excessive pressure (not for steam service). Primarily used on storage tanks, P1000AXL materials include cast brass or bronze for the main valve body, quality stainless steel 300 series internals, stainless steel springs, and FDA approved, epoxy-coated copper tube probes. Multiple pressure relief settings and inlet/outlet connection options provide easy, ultra versatile installation capabilities, and the P1000AXL assembly shall be used where pressure only relief is required.
- Eliminates risk of over-pressure of storage tanks.
- Epoxy-coating adds extra protection.
- Pressure relief valve set at 150 psi.
- CSA Compliance to ANSI Z21.22/CSA 4.4.
- Certified to ASME Section IV by National Board.
- Pressure relief valve settings of 30, 75, 125, and 150 psi offer versatility.
Every item checked for quality -
interhasa! Electric Hand Dryer for Commercial Bathrooms
$329.00 $180.95- UPDATED 3rd GENERATION HAND DRYER — This updated Jet hand dryer uses a more powerful main board, thinner cover design, lower noise, and lower power consumption technology. High quality ABS Material and updated structure ensures the product’s life time. Its elegant design makes it a premium decor for all commercial bathrooms.
- HIGH SPEED HAND DRYER – Double-sided Jet design with ultra high speed. 1800 Watts 95m/s air dryer, fast drying within 5-7 seconds, 3 times faster than compact hand dryers. Its speedy dry time and highly refined design creates a refreshing lifestyle and better customer experience in a high traffic area.
- HEPA FILTER – This bathroom hand dryer with built-in high quality HEPA filter is more hygienic. It cleans the air and provides absolutely pure air flow. The detachable air filters can also prevent dust from entering the machine, which also can promise the long life of the air hand dryer.
- LOWER NOISE & ENERGY CONSUMPTION – This electric hand dryer dries hands in less than 7 Seconds using 80% less energy than Normal warm Hand Dryer. Largely saves Electricity and Costs less to run. The best Hand Drying alternative for any environment with 70% smaller carbon footprint than Paper Towels.
- WALL MOUNTED & EASY INSTALLATION – With a modern and sleek design, this jet hand dryer is suitable for public school, hospital, star hotels, airports, shopping malls, restaurant, and other consistently high-traffic restrooms.
Every item checked for quality -
EcoSmart 120-Watt Equivalent PAR38 CEC Motion Sensor Flood LED Light Bulb Bright White (2-Pack)
$21.09 $11.60The EcoSmart LED Motion Activated Security Floodlights easily convert existing outdoor flood lights to LED motion sensing security lights in seconds. The built-in radar motion sensor detects motion within a 25 ft. range and keeps lights on for 1-minute after the last detected movement. The sensor detection angle is 100. Radar technology is more reliable and longer lasting than traditional infrared sensing. The built-in daylight sensor keeps daytime motion from triggering the lights. For 24/7 operation, the motion and daylight sensors can be easily deactivated by a simple flip of the light switch. Great for under eaves, backyards, driveways, doorways and more.
- Radar motion sensor 25 ft. detection range.
- 100° detection angle.
- Daylight sensor keeps daytime motion from triggering the lights.
- Easily deactivate sensors to allow for constant 24/7 bulb operation.
- Switch lights ON for normal motion sensor mode.
- Switch OFF, then back ON (within 3-seconds) for always-on, 24/7 operation.
- Switch OFF (for longer than 3 seconds) then back ON to re-activate motion sensor mode.
- 120-Volt, E26 PAR38 bulbs, non-dimmable, 2-pack.
- 1200 Lumens each bulb.
- Not for use with existing motion sensor fixtures.
- Light appearance: 3,000K (bright white).
- California Energy Commission Title 20 Compliant LED Light Bulb.
Every item checked for quality -
American Standard Children’s Round Open Front Toilet Seat in White
$44.64 $24.55EverClean antimicrobial surface inhibits the growth of stain- and odor-causing bacteria, mold, and mildew on the surface.
- Model # 5001G055.020.
- For Baby Devoro bowls 2315.228 and 2282.001.
- Open front toilet seat less cover.
- Injection molded solid polypropylene.
- Plastic material.
Every item checked for quality -
3/4-in 90-Degree Schedule 40 PVC Conduit Elbow Conduit Fittings
$1.58 $0.87This is a piece of schedule 40 conduit which has been heated and bent to effect a 90° change in direction in a conduit run.- Schedule 40 nonmetallic PVC construction for strength and durability.
- For indoor or outdoor use.
- Suitable for above ground or can be buried.
- Bell end for easy installation.
- ETL listed conforms to UL 651 and NEMA TC-3 conforms to UL 651 and NEMA TC-3.
Every item checked for quality -
Steel City 2-Gang New Work Square Device Electrical Wall Box (Case of 10)
$65.29 $35.91Mount electrical switches and receptacles to wood or metal wall studs with the 2-Gang Square Device Wall Box. This wall box can be used in indoor and outdoor residential and commercial applications. It offers welded construction with 3/4 in. and 1/2 in. eccentric knockouts and ground bump.
- Model # 2G4D1234-10R.
- Use to mount electrical switches and receptacles to wood or metal wall studs with 3/8 in. offset.
- Zinc-galvanized steel is rust- and corrosion resistant.
- Compatible with electrical conduit wiring in indoor/outdoor residential and commercial applications.
- UL Listed.
- 17 knockouts for use with 1/2 in. and 3/4 in. connections.
Every item checked for quality -
BrassCraft 1/2 in. MIP x 1/2 in. MIP x 24 in. Gas Connector (1/2 in. O.D.) with Safety+Plus2 Thermal Excess Flow Valve (85,000 BTU)
$27.27 $15.00BrassCrafts Safety+PLUS2 gas connector combines patented excess flow technology and thermal heat activation with the advanced corrosion resistance, to provide a safer gas connector for your home and family. In the event of a gas line rupture or disconnect, the excess flow valve (EFV) restricts gas flow at the appliance to a non-hazardous level. This immediate action helps avert the potential for a dangerous release of gas into the home. Gas is controlled only at the point where the problem exists; the rest of your system will continue to function. Safety+PLUS EFV automatically resets once the gas line is properly repaired. The thermal component utilizes a thermal ring that will restrict the flow through the valve when the valve is exposed to temperatures of 400F or more. BrassCraft’s stainless steel gas connector also features a proprietary polymer coating designed to withstand prolonged exposure to harsh household cleaning, plumbing repair and masonry products as well as UV rays and salt. Unlike conventional dipped or sprayed coatings, the ProCoat coating is baked directly on the connector surface at high temperatures to provide a uniform coating over the entire length of the connector. The coating is applied only after the connector has been 100% leak tested to provide complete corrosion resistance.
Every item checked for quality
