Showing 46–52 of 52 results
-
Apollo 3/4 In. X 3/4 In. Pvc Schedule 40 Slip X Slip Ball Valve Pro Pack (12-Pack)
$18.18 $10.00PVC Sch. 40 Ball Valves are compact and lightweight. This Slip x Slip valve is designed for a variety of applications including pressure distribution of cold water in irrigation, pool, spa, agricultural, commercial and light industrial applications and comes in a plastic jar of 12 valves which is convenient, resealable, and reusable. The ball valves are NSF approved and have EPDM seats and O-rings integrated into the durable PVC body.
- PVC schedule 40 construction for durability.
- Full port design allows for maximum efficiency and minimal turbulence or pressure reduction.
- Quarter-turn flow control for easy on and off.
- NSF / ANSI standard 372 certified.
- Slip connections conform to ASTM D2467.
- Working temperature range: 41°F to 122°F (5°C to 55°C).
- Maximum pressure rating 150 psi at 73°F (22°C).
- Requires solvent cement for installation (not included).
- Please note – as temperature increases, working pressure decreases, the optimal working pressure for PVC valves is 150 psi at 73°F (22°C) if the temperature increases above 73°F (22°C), use the PVC. correction factor to determine working pressure, multiply the maximum working pressure by the correction factor, please see correction factor grid on the attached specification sheet.
Every item checked for quality -
BrassCraft 1/2 in. Push Connect Inlet x 3/8 in. Compression Outlet 1/4-Turn Straight Valve, #73
$5.45 $3.00
BrassCraft 1/2 in. Nominal Push Connect Inlet x 3/8 in. O.D. Compression Outlet 1/4-Turn Straight Valve controls water flow to household plumbing fixtures. The straight valve is most often used where the water pipe enters the room from the floor. With a 90° turn of the valve handle, you are able to stop the flow of water leading to the plumbing fixture, allowing for maintenance and repair without shutting off the water to the entire home. Push Connect valves are installation ready requiring no special tools, soldering or glue for a watertight seal.
- Compatible with PEX, copper and CPVC.
- Smooth, quarter-turn operation, on/off flow control with a 90° turn of the handle.
- Installation ready: requires no special tools, soldering or glue for a watertight seal.
- 1-piece shut-off mechanism ensures smooth operation without freeze-ups even after long periods without use.
- Pre-inserted tube stiffener is “installation ready” for a faster connection.
- Easy-to-remove handle protects against accidental operation during rough-ins.
- Chrome-plated brass.
- Temperature rating: 40° to 160°F.
- Pressure rating: 125 psi maximum.
- No-lead certified.
- IAPMO and CSA listed to ASME A112.18.1/CSA B125.1.
Every item checked for quality -
HOME-FLEX 1/2 in. CSST x 1/2 in. FIPT Brass Female Adapter
$10.13 $5.57The HOME-FLEX Female Adapter allows you to quickly affix a CSST system to a gas source. Used to attach CSST directly to Steel Pipe. Can attach CSST either the beginning or end of a CSST system.
- Very high quality brass construction.
- 1/2 in. diameter.
- For use with HOME-FLEX CSST systems.
- For use with natural gas or liquid propane.
- CSA and IAPMO certified.
- Not for use with Home Flex UNDERGROUND poly tubing.
- HOME-FLEX Corrugated Stainless Steel Tubing (CSST) flexible gas piping material must be installed by a qualified installer who has been certified in the use of the HOME-FLEX gas piping system.
- Some areas of the United States do not allow installation of CSST for fuel gas piping systems. It is the installer’s responsibility to check and understand all codes governing the location of installation prior to installing HOME-FLEX CSST.
- CSST is generally for indoor use; however, it can be used outdoors and/or underground with very specific parameters.
Every item checked for quality -
Cash Acme 3/8 in. Compression HG-135 Thermostatic Mixing Valve with Compression Tee
$78.40 $43.12The HG135 is a sleek and compact point of use mixing valve designed to assist in the prevention of scalding. It features a superior, fast acting thermostatic element that provides stable operation at flow rates as low as 0.25 gm (0.95 pm). The Heatguard 135 also reduces the outlet flow to a trickle in the event of a cold water supply failure. The valve inlets and outlet connections are standard 3/8″ supply line compression connections for use with 3/8 in. OD tube. The inlets of the valve feature check valves to prevent cross contamination as well as serviceable strainer screens to prevent the valve from being clogged with dirt or debris. Each valve includes a purpose built mounting bracket and hardware to neatly and securely fasten the valve to the wall. The compact design and pleasant aesthetics allow for this valve to easily be fit under or behind a single basin. Adjustable outlet temperature range: 100°-120°F (38°-49°C).
- Intended for point of use/under sink installations to provide safe outlet water temperature.
- Ideal for individual faucets and electronic faucets.
- ASSE 1070 approved.
- Listed by ASSE, CSA, IAPMO.
- Accurate temperature control with flows as low as 0.25 gpm.
- Robust, low complexity design and total flow shut-off if cold supply fails.
Every item checked for quality -
BrassCraft Safety+PLUS2 Thermal Excess Flow valve (36,800 BTU) 1/2 in. MIP x 1/2 in. MIP x 24 in. Gas Connector
$27.27 $15.00BrassCraft’s Safety+PLUS2 gas connector combines patented excess flow technology and thermal heat activation with the advanced corrosion resistance, to provide a safer gas connector for your home and family. In the event of a gas line rupture or disconnect, the excess flow valve (EFV) restricts gas flow at the appliance to a non-hazardous level. This immediate action helps avert the potential for a dangerous release of gas into the home. Gas is controlled only at the point where the problem exists; the rest of your system will continue to function. Safety+PLUS EFV automatically resets once the gas line is properly repaired. The thermal component utilizes a thermal ring that will restrict the flow through the valve when the valve is exposed to temperatures of 400°F or more. BrassCraft’s stainless steel gas connector also features a proprietary polymer coating designed to withstand prolonged exposure to harsh household cleaning, plumbing repair and masonry products as well as UV rays and salt. Unlike conventional dipped or sprayed coatings, the ProCoat coating is baked directly on the connector surface at high temperatures to provide a uniform coating over the entire length of the connector. The coating is applied only after the connector has been 100% leak tested to provide complete corrosion resistance.
- Corrugated stainless steel with corrosion resistant coating.
- 1/4 in. ID (3/8 in. OD).
- Connectors and fittings can be used with natural gas, LP gas (propane) and LP gas-air mixtures.
- Use to install 4-burner gas ranges, cook-top, dryers and water heaters.
- Safety+Plus2 TEFV valve helps protect against fires and explosions.
- Valve has no parts that can break or misalign over time for 24/7 protection.
- Connector and valve are 100% leak tested.
- No special tools required for installation.
- ProCoat coating corrosion resistant to most household chemicals, UV rays and salt.
- Approved for indoor and outdoor use.
- Temperature rating: -20°F to 150°F.
- Pressure rating: 1/2 psi maximum.
- ANSI Z21.24-2015/CSA 6.10-2015 and ANSI Z21.75-2016/CSA 6.27-2016, ANSI Z21.93-17/CSA 6.30-17.
- Designed, machined and assembled in the USA.
Every item checked for quality -
#2, STRM005CR, Chrome Single Lever Pull-Down Kitchen Faucet
$100.00 $55.00- Model: Star Mini Pull-Out Kitchen Mixer – STRM005CR.
- Function: Single Lever Pull-Down Kitchen Mixer/Faucet.
- Configuration: Single-Hole Installation.
- Finish: Chrome.
- Brand: Modern National.
- Manufacturer: Enping MN Kitchen & Bathroom Co., Ltd.
- Installation Instructions are Included.
Every item checked for quality -
SharkBite Push-to-Connect Faucet Installation Kit
$36.36 $20.00The SharkBite Faucet Installation Kit has everything you need to install your new faucet. The kit includes 2 SharkBite 1/2 in. x 1/4 in. (3/8 in. O.D.) Push-to-Connect Angle Stop Valves, two 5 ft. coils of 1/4 in. PEX Pipe, two 1/4 in. (3/8 in. O.D.) SharkBite x 1/2 in. Swivel Faucet Connectors, and a 1/2 in. Chrome Trim Cover reversed functions as a disconnect and 1/4 in. disconnect clip to remove the pipe from the fitting if needed. The SharkBite Angle Stop Valves work with copper, PEX or CPVC. Just insert the pipe and the stainless steel teeth bite down and grip tight, while a specially formulated O-ring compresses to create a perfect seal. Disassembly is just as fast using the simple disconnect tool so fittings and valves can be easily changed and reused. They can even be rotated after assembly for easier installation in tight spaces. The included PEX coils can be cut to the exact length needed so there is no excess supply line to coil up under the sink providing a clean, tangle free look. Once the stop valves are installed, thread the 1/2 in. faucet connectors onto the faucet connections and then measure and cut the PEX and push into the outlet on the stop valve and the faucet connector and the installation is complete.
Every item checked for quality
