Showing 46–54 of 260 results
-
SunTouch Floor Warming 4 ft. x 30 in. 120-Volt Radiant Floor Heating Mat (Covers 10 sq. ft.)
$169.51 $93.23The SunTouch Floor Heating Mat measures 4 ft. x 30 in. and offers an ultra-thin, low-profile system that installs beneath tile, stone and even vinyl or laminate flooring. Its ideal for remodeling bathrooms and kitchens to add radiant floor heating and offers an upscale option when designing new construction floor warming. Dual-wire technology reduces electromagnetic fields (EMF) to ultra-low levels. The mat is an energy-efficient touch of radiant floor warming luxury for your home, is UL listed, and comes with detailed installation instructions.
- Install the heated floor mat below ceramic or porcelain tile, stone or brick floors or in a self-leveling mortar bed below vinyl floors, floating wood- and laminate floors.
- For indoor floor-warming use only.
- Open-weave construction for easy application of thin-set and mortar without compromising the bond of your floor covering to the sub-floor.
- Dual wire technology keeps EMF to ultra-low levels.
- UL listed for safety.
- Energy efficient, inexpensive to operate.
- Armored power lead wire straight to the electrical box, no conduit required.
- Single-point power connection to facilitate layout and wiring.
- Mats can be connected in parallel for larger floor surfaces.
- Can be combined with a programmable thermostat control (not included).
Every item checked for quality -
WIEGMANN Indoor Enclosure 6 in. x 6 in. x 4 in. NEMA 1 Screw Cover/Pull Box
$25.98 $14.29WIEGMANN 6 in. x 6 in. x 4 in. screw cover pull box is made of pre-galvanized steel and designed for indoor locations. The product is ideal for surface mounting or allows runs of conduit for power or communication conductors. Boxes have flat, removable covers fastened with screws. Holes are provided in back for mounting. NEMA 1 enclosures are intended for indoor use, primarily to provide a degree of protection against contact with the enclosed equipment in locations where unusual service conditions do not exist. The enclosures shall meet the rod entry and resistance tests.- Model #SC060604RC.
- Designed for use as wiring boxes and junction boxes.
- Provide a degree of protection against contact with the enclosed equipment.
- ANSI-61 gray polyester powder inside and out.
- Removable concentric knockouts on all four sides.
- Mounting holes provided on back of enclosure.
- Cover easily removed without extracting cover screws.
Every item checked for quality -
2″ Insulated Ground Bushing
$4.67 $2.57Bridgeport 386-DC 2″ Die Cast w/Plastic Metaliner Insulated Grounding Bushing for Rigid/IMC Conduit.
- Material: Ball Burnished Mirror Smooth Die-Cast Zinc.
- Approval: UL 514B, UL (Canada and US).
- Used On: IMC/Rigid Conduit.
- Additional Information: ROHS Compatible; Applicable Standard Federal Specification A-A-50553, NEMA FB-1; Insulator Material Nylon; Insulation Temperature 150 Deg C.
- Type: Threaded.
- Trade Size: 2 Inch.
- Wire Size: 14 AWG Solid to 1/0 AWG Stranded.
- Lug Type: Tin Electroplated 6061-T6 Aluminum Alloy.
- Throat Type: Insulated.
- Diameter: 2-5/8 Inch.
- Height: 1/16 Inch.
Every item checked for quality -
BrassCraft 1/2 in. MIP x 1/2 in. MIP x 48 in. Gas Connector (3/8 in. O.D.) with Safety+Plus2 Thermal Excess Flow Valve (28,300 BTU)
$27.27 $15.00BrassCrafts Safety+PLUS2 gas connector combines patented excess flow technology and thermal heat activation with the advanced corrosion resistance, to provide a safer gas connector for your home and family. In the event of a gas line rupture or disconnect, the excess flow valve (EFV) restricts gas flow at the appliance to a non-hazardous level. This immediate action helps avert the potential for a dangerous release of gas into the home. Gas is controlled only at the point where the problem exists; the rest of your system will continue to function. Safety+PLUS EFV automatically resets once the gas line is properly repaired. The thermal component utilizes a thermal ring that will restrict the flow through the valve when the valve is exposed to temperatures of 400F or more. BrassCraft’s stainless steel gas connector also features a proprietary polymer coating designed to withstand prolonged exposure to harsh household cleaning, plumbing repair and masonry products as well as UV rays and salt. Unlike conventional dipped or sprayed coatings, the ProCoat coating is baked directly on the connector surface at high temperatures to provide a uniform coating over the entire length of the connector. The coating is applied only after the connector has been 100% leak tested to provide complete corrosion resistance.
- Corrugated stainless steel with corrosion resistant coating.
- 1/4 in. I.D. (3/8 in. O.D.).
- Connectors and fittings can be used with natural gas, LP gas (propane) and LP gas-air mixtures.
- Use to install 4-burner gas ranges, cook-top, dryers and water heaters.
- Safety+Plus2 TEFV valve helps protect against fires and explosions.
- Valve has no parts that can break or misalign over time for 24/7 protection.
- Connector and valve are 100% leak tested.
- No special tools required for installation.
- ProCoat coating corrosion resistant to most household chemicals, UV rays and salt.
- Approved for indoor and outdoor use.
- Temperature rating: -20°F to 150°F.
- Pressure rating: 1/2 psi maximum.
- ANSI Z21.24-2015/CSA 6.10-2015 and ANSI Z21.75-2016/CSA 6.27-2016, ANSI Z21.93-17/CSA 6.30-17.
- Designed, machined and assembled in the USA.
Every item checked for quality -
1-1/2 MNPT PVC Terminal Conduit Adapter
$1.78 $0.98TA30 Scepter rigid PVC conduit pipe and fittings are non-sparking and non-conducting, thereby eliminating the most dangerous second point of contact and phase to ground faults. The use of a separate grounding conductor in a Scepter PVC conduit system gives a complete and positive ground for the whole system.
Every item checked for quality -
Black Pop up Sink Drain Stopper with Overflow, Bathroom Faucet Lavatory Vessel Pop Up
$18.18 $10.00
Press the top of the pop-up to close, and another press to open. Durable solid brass construction ensured quality and longevity. Please make sure the gaskets are in the right position to avoid leakage. Black finish build to resist daily scratches and corrosions. Fits hole diameter 1.57 inch to 1.92 inch & sink thickness 0.98 inch to 1.88 inch.Every item checked for quality -
RUGPADUSA Essentials 9 ft. x 12 ft. Hard Surface 100% Felt 1/4 in. Thickness Rug Pad
$87.51 $48.13If you’re looking for some cushion under your rugs that won’t break the bank, RUGPADUSA Essentials is for you. These felt rug pads are 1/4 in. thick 100% recycled fiber. They add comfort underfoot and help with noise reduction on rugs that don’t require a non-slip pad. Our pads are manufactured and made to withstand heavy traffic while protecting your rugs and your floors. We stock Essentials in the most common sizes for rugs, and they can easily be modified with a pair of household scissors.
- 100% felt padding buffers foot traffic, traps dirt, and prolongs the life of rugs and floor surfaces.
- Needle-punched felt.
- Dense, thick felt provides cushion underfoot.
- Will not strip, discolor, or damage any floor surfaces.
- Made with 100% pre-consumer, recycled fibers for long lasting comfort and durability.
- Low VOC emissions keep your family safe from harmful irritants.
Every item checked for quality -
Sharkbite Prolock 1 In. Push-To-connect Plastic 90-Degree Elbow Fitting Pro Pack (3-Pack)
$28.96 $15.93SharkBite ProLock fittings are a versatile and innovative full-flow plumbing system utilizing push lock fitting technology and engineered specifically for use with SharkBite PE-RT and PEX pipe. The SharkBite 1 in. Push-to-Connect 90° Elbow intuitive design makes for one of the simplest and most dependable fittings on the market. No tools are required to make a connection. They use a collet with stainless steel teeth that grips the pipe when fully inserted, and an EPDM O-Ring to provide a permanent, leak-proof seal. The Twist-to-lock technology ensures maximum security. When twisted into place with indicator arrows aligned, the locking cap locks the pipe in place and creates an audible click. Removing a SharkBite fitting is just as easy with no tools needed; simply twist the cap turn counterclockwise to unlock then depress collet against the fitting to remove the pipe. ProLock fittings are suitable for hot and cold potable water and hydronic heating applications. They have been specifically designed for the Professional Plumber. Code approved for behind-the-wall installations.
Every item checked for quality
