Showing 1–9 of 64 results
-
BrassCraft 1/2 in. MIP x 3/8 in. FIP x 24 in. Stainless Steel Gas Connector w/Safety+Plus2 Thermal Excess Flow Valve (36,800 BTU)
$27.27 $15.00BrassCraft’s Safety+PLUS2 gas connector combines patented excess flow technology and thermal heat activation with the advanced corrosion resistance, to provide a safer gas connector for your home and family. In the event of a gas line rupture or disconnect, the excess flow valve (EFV) restricts gas flow at the appliance to a non-hazardous level. This immediate action helps avert the potential for a dangerous release of gas into the home. Gas is controlled only at the point where the problem exists; the rest of your system will continue to function. Safety+PLUS EFV automatically resets once the gas line is properly repaired. The thermal component utilizes a thermal ring that will restrict the flow through the valve when the valve is exposed to temperatures of 400°F or more. BrassCraft’s stainless steel gas connector also features a proprietary polymer coating designed to withstand prolonged exposure to harsh household cleaning, plumbing repair and masonry products as well as UV rays and salt. Unlike conventional dipped or sprayed coatings, the ProCoat coating is baked directly on the connector surface at high temperatures to provide a uniform coating over the entire length of the connector. The coating is applied only after the connector has been 100% leak tested to provide complete corrosion resistance.
- Corrugated stainless steel with corrosion resistant coating.
- 1/4 in. ID (3/8 in. OD).
- Connectors and fittings can be used with natural gas, LP gas (propane) and LP gas-air mixtures.
- Use to install 4-burner gas ranges, cook-top, dryers and water heaters.
- Safety+Plus2 TEFV valve helps protect against fires and explosions.
- Valve has no parts that can break or misalign over time for 24/7 protection.
- Connector and valve are 100% leak tested.
- No special tools required for installation.
- ProCoat coating corrosion resistant to most household chemicals, UV rays and salt.
- Approved for indoor and outdoor use.
- Temperature rating: -20°F to 150°F.
- Pressure rating: 1/2 psi maximum.
- ANSI Z21.24-2015/CSA 6.10-2015 and ANSI Z21.75-2016/CSA 6.27-2016, ANSI Z21.93-17/CSA 6.30-17.
- Designed, machined and assembled in the USA.
Every item checked for quality -
Everbilt 30/50 Low Pressure Switch For Well Pumps
$30.82 $16.95This pressure switch signals the pump to start when the water system drops to 30 PSI (factory set) and stops at 50 PSI (factory set). This switch is to be used with submersible well or jet pumps. It can be wired 115-Volt or 230-Volt. This switch must be used in conjunction with a well pressure tank. The air pressure in the well tank, when empty of all water, must be set to 28 PSI, or the switch will not operate properly. This switch is equipped with a low-level cut-off arm that automatically shuts off a well pump when there is a dramatic decrease in pressure, such as a leak in the discharge pipes or a faulty pressure tank.
- Turns pump on at 30 psi, off at 50 psi.
- Cap removes for easy adjustment.
- Can be wired 115-Volt or 230-Volt.
- For use with submersible well or jet pumps.
- Motor wires are connected to the 2 middle posts (color does not matter).
- Breaker box wires are connected to 2 outside posts (color does not matter).
- 2-spring design allows for adjustment of cut-in and cut-out pressure settings.
- Adjustments to springs should only be made by users with good knowledge of well systems.
- Switch shuts off pump automatically when there is a dramatic decrease in pressure.
Every item checked for quality -
Charlotte Pipe 4 in. x 4 in. x 1-1/2 in. PVC DWV Wye Reducing
$38.82 $21.35PVC fittings are for drain, waste and vent purposes. They are used in gravity-fed waste elimination systems and are for Non-Pressure systems where temperatures will not exceed 140F. PVC is lightweight and easy to install. They require no special tools for cutting and can be installed with solvent cementing, threading, flanging and roll-grooved joining.
Every item checked for quality -
Everbilt 3/4 in. Compression x 3/4 in. MIP Brass Adapter Fitting
$12.98 $7.14Use these Camco 3/4 in. x 3/4 in. brass compression fittings for evaporative coolers to create a watertight connection at the end of an evaporative cooler pipe and fitting. Measurement is 3.63 in. in width and 5.5 in. in height. No solder or adhesives are needed for installation.
- Compatible with most evaporative cooler pipes measuring 3/4 in. x 3/4 in.
- Watertight fit.
- Durable brass construction.
- Used to create a watertight connection between a pipe, fitting and evaporative cooler.
- Installs easily without solder or adhesives.
Every item checked for quality -
BrassCraft 1/2 in. MIP x 1/2 in. MIP x 48 in. Gas Connector (1/2 in. OD) w/Safety+Plus2 Thermal Excess Flow Valve (60,500 BTU)
$27.27 $15.00BrassCrafts Safety+PLUS2 gas connector combines patented excess flow technology and thermal heat activation with the advanced corrosion resistance, to provide a safer gas connector for your home and family. In the event of a gas line rupture or disconnect, the excess flow valve (EFV) restricts gas flow at the appliance to a non-hazardous level. This immediate action helps avert the potential for a dangerous release of gas into the home. Gas is controlled only at the point where the problem exists; the rest of your system will continue to function. Safety+PLUS EFV automatically resets once the gas line is properly repaired. The thermal component utilizes a thermal ring that will restrict the flow through the valve when the valve is exposed to temperatures of 400F or more. BrassCraft’s stainless steel gas connector also features a proprietary polymer coating designed to withstand prolonged exposure to harsh household cleaning, plumbing repair and masonry products as well as UV rays and salt. Unlike conventional dipped or sprayed coatings, the ProCoat coating is baked directly on the connector surface at high temperatures to provide a uniform coating over the entire length of the connector. The coating is applied only after the connector has been 100% leak tested to provide complete corrosion resistance.
Every item checked for quality -
BrassCraft 1/2 in. Nominal Push Connect x 1/2 in. FIP x 20 in. SpeediOne Braided Faucet Connector and 1/4-Turn Straight Valve
$3.64 $2.00Original Retail Price: $17.75.
BrassCraft’s push connect one-piece water supply combines their trusted brass water valve with their flexible braided polymer connector for one quick easy-to-install solution. BrassCraft’s one-piece connection features push connect technology on the valve inlet and a hand-tighten wing nut on the outlet to provide a significant savings in installation time and cost. Push connect valve inlet requires no special tools to install and comes equipped with a pre-inserted tube stiffener to make the product ideal for copper, PEX and CPVC piping systems. The braided polymer fibers of the connector are designed to bend freely without kinking or crimping in tight quarters and resist corrosion caused by chemicals found in common household, tile and glass cleaners. In addition, its reinforced inner hose resists corrosion under harsh water conditions.
- 1-piece unit combines valve and supply line.
- Saves time with one less connection.
- No special installation tools required.
- Installation ready with pre-inserted tube stiffener.
- Fast, reliable and secure.
- Compatible with copper, PEX and CPVC.
- Remove with combination removal tool or 5/8 in. open end wrench.
- Connector bends freely without kinking or crimping in tight quarters.
- No-lead certified.
- IAPMO and CSA listed to ASME A112.18.1/CSA B125.1.
Every item checked for quality -
Everbilt 1/10 HP Non-Submersible Self-Priming Transfer Pump
$109.09 $60.00The Everbilt 1/10 HP non-submersible self-priming transfer pump is designed for portable and residential applications. It can drain or remove water from window wells, clogged sinks, basements, water basins, stock tanks, boats, fish tanks, water heaters, swimming pool covers, low spots in yards, or other flooded areas. It is not approved for use in swimming pools or in salt-water marine areas.
- Includes 6 ft. suction hose, suction strainer, puddle strainer and a set of replacement motor brushes.
- Made of high strength, corrosion resistant materials for trouble free service for years.
- Pump clear water; do not pump fuel or other flammable liquids.
- Pump not intended to be permanently installed.
- Not intended for use in sewage or septic systems.
- To help prolong the life of the impeller, before each use it is recommended to fill the motor housing with 1-2 teaspoons of water or vegetable oil.
- Maximum discharge head of 48 ft.
- Motor is fan cooled and thermally protected.
- 8.36 ft. power cord.
Every item checked for quality -
BrassCraft 1/2 in. MIP x 1/2 in. MIP x 36 in. Gas Connector (3/8 in. O.D.) w/Safety+Plus2 Thermal Excess Flow Valve (33,400 BTU)
$27.27 $15.00BrassCrafts Safety+PLUS2 gas connector combines patented excess flow technology and thermal heat activation with the advanced corrosion resistance, to provide a safer gas connector for your home and family. In the event of a gas line rupture or disconnect, the excess flow valve (EFV) restricts gas flow at the appliance to a non-hazardous level. This immediate action helps avert the potential for a dangerous release of gas into the home. Gas is controlled only at the point where the problem exists; the rest of your system will continue to function. Safety+PLUS EFV automatically resets once the gas line is properly repaired. The thermal component utilizes a thermal ring that will restrict the flow through the valve when the valve is exposed to temperatures of 400F or more. BrassCraft’s stainless steel gas connector also features a proprietary polymer coating designed to withstand prolonged exposure to harsh household cleaning, plumbing repair and masonry products as well as UV rays and salt. Unlike conventional dipped or sprayed coatings, the ProCoat coating is baked directly on the connector surface at high temperatures to provide a uniform coating over the entire length of the connector. The coating is applied only after the connector has been 100% leak tested to provide complete corrosion resistance.
- Corrugated stainless steel with corrosion resistant coating.
- 1/4 in. I.D. (3/8 in. O.D.).
- Connectors and fittings can be used with natural gas, LP gas (propane) and LP gas-air mixtures.
- Use to install 4-burner gas ranges, cook-top, dryers and water heaters.
- The Safety+Plus2 TEFV valve helps protect against fires and explosions.
- Valve has no parts that can break or misalign over time for 24/7 protection.
- Connector and valve are 100% leak tested.
- No special tools required for installation.
- ProCoat coating corrosion resistant to most household chemicals, UV rays and salt.
- Approved for indoor and outdoor use.
- Temperature rating: -20°F to 150°F.
- Pressure rating: 1/2 psi maximum.
- ANSI Z21.24-2015/CSA 6.10-2015 and ANSI Z21.75-2016/CSA 6.27-2016, ANSI Z21.93-17/CSA 6.30-17.
- Designed, machined and assembled in the USA.
Every item checked for quality -
Everbilt Shower Mixing Valve Collar for Shower Valves and Handles
$10.47 $5.76The Everbilt waterproof mixing valve collars are designed to seal mixing shower valves to prevent leaking and mold growth. These thin, high-quality, reliable mixing valve collars are made from very strong, tear-resistant polyethylene fibers that prevents moisture from penetrating deep into walls, and offers optimum connection to tile laying materials. Thus, the Everbilt mixing valve collars provide an excellent watertight seal, are 100% waterproof, and top rated for steam shower applications. Installation is easy over smooth, shower wall surfaces as these collars can be fixed in place with modified or non-modified thin-set mortar suitable for tile or stone finishes. The package includes one mixing valve collar, and is part of the Everbilt waterproofing kit, along with the Everbilt pipe collar, Everbilt inside corners and Everbilt outside corners, sold separately. Thickness 0.1 in.
- Designed to seal mixing shower valves to prevent leaking and mold growth.
- Thin, high-quality, reliable.
- Made from very strong, tear-resistant polyethylene fibers that prevents moisture from penetrating deep into walls.
- Provides an excellent watertight seal.
- 100% Waterproof.
- Top rated for steam shower applications.
- Can be fixed in place with modified or non-modified thin-set mortar.
- Includes one piece of mixing valve collar.
- Also included in Everbilt waterproofing kit.
Every item checked for quality
