Showing 28–36 of 52 results
-
Charlotte Pipe 2 in. PVC DWV 22-1/2-Degree Hub x Hub Street Elbow Fitting
$5.31 $2.92PVC fittings are for drain, waste and vent purposes. They are used in gravity-fed waste elimination systems and are for Non-Pressure systems where temperatures will not exceed 140°F. PVC is lightweight and easy to install. They require no special tools for cutting, and can be installed with solvent cementing, threading, flanging, and roll-grooved joining.
Every item checked for quality -
BrassCraft 1/2 in. Push Connect Inlet x 3/8 in. Compression Outlet 1/4-Turn Straight Valve, #73
$5.45 $3.00
BrassCraft 1/2 in. Nominal Push Connect Inlet x 3/8 in. O.D. Compression Outlet 1/4-Turn Straight Valve controls water flow to household plumbing fixtures. The straight valve is most often used where the water pipe enters the room from the floor. With a 90° turn of the valve handle, you are able to stop the flow of water leading to the plumbing fixture, allowing for maintenance and repair without shutting off the water to the entire home. Push Connect valves are installation ready requiring no special tools, soldering or glue for a watertight seal.
- Compatible with PEX, copper and CPVC.
- Smooth, quarter-turn operation, on/off flow control with a 90° turn of the handle.
- Installation ready: requires no special tools, soldering or glue for a watertight seal.
- 1-piece shut-off mechanism ensures smooth operation without freeze-ups even after long periods without use.
- Pre-inserted tube stiffener is “installation ready” for a faster connection.
- Easy-to-remove handle protects against accidental operation during rough-ins.
- Chrome-plated brass.
- Temperature rating: 40° to 160°F.
- Pressure rating: 125 psi maximum.
- No-lead certified.
- IAPMO and CSA listed to ASME A112.18.1/CSA B125.1.
Every item checked for quality -
NIBCO 4 in. x 2 in. PVC DWV Spigot x Hub Flush Bushing
$7.67 $4.22The NIBCO 4 in. x 2 in. PVC DWV Spigot x Hub Flush Bushing can be inserted into a PVC sitting hub to reduce the hub to a smaller pipe size. The bushing is designed for use with drain, waste and vent piping systems. PVC fittings exhibit high corrosion and chemical resistance and will not rust, scale, pit or corrode.
Every item checked for quality -
#7, BrassCraft 3/8 in. FIP Inlet x 3/8 in. Compression Outlet 1/4-Turn Angle Valve
$5.45 $3.00
The BrassCraft 3/8 in. FIP Inlet x O.D. Compression Outlet 1/4-Turn Angle Valve allows you to control water flow easily and quickly. It’s used where the water pipe enters the room from the wall and it controls flow to plumbing fixtures including washing machines, toilets, faucets and more. This valve allows you to simply turn the handle when you need to do repairs or maintenance without turning the water off to the whole house.
- Compatible with iron pipe.
- Smooth on/off flow control with a quarter turn (90 degrees ) turn of the handle.
- One-piece shut-off mechanism ensures smooth operation without freeze-ups even after long periods without use.
- Easy-to-remove handle protects against accidental operation during rough-ins.
- One-piece body construction for strength, durability and long-lasting performance.
- Chrome-plated brass.
- Temperature rating: 40 degrees to 160 degrees F.
- Pressure rating: 125 PSI maximum.
- No-lead certified.
- IAPMO and CSA listed to ASME A112.18.1/CSA B125.1.
Every item checked for quality -
BrassCraft 1/2 in. MIP x 1/2 in. MIP x 48 in. Gas Connector (3/8 in. O.D.) with Safety+Plus2 Thermal Excess Flow Valve (28,300 BTU)
$27.27 $15.00BrassCrafts Safety+PLUS2 gas connector combines patented excess flow technology and thermal heat activation with the advanced corrosion resistance, to provide a safer gas connector for your home and family. In the event of a gas line rupture or disconnect, the excess flow valve (EFV) restricts gas flow at the appliance to a non-hazardous level. This immediate action helps avert the potential for a dangerous release of gas into the home. Gas is controlled only at the point where the problem exists; the rest of your system will continue to function. Safety+PLUS EFV automatically resets once the gas line is properly repaired. The thermal component utilizes a thermal ring that will restrict the flow through the valve when the valve is exposed to temperatures of 400F or more. BrassCraft’s stainless steel gas connector also features a proprietary polymer coating designed to withstand prolonged exposure to harsh household cleaning, plumbing repair and masonry products as well as UV rays and salt. Unlike conventional dipped or sprayed coatings, the ProCoat coating is baked directly on the connector surface at high temperatures to provide a uniform coating over the entire length of the connector. The coating is applied only after the connector has been 100% leak tested to provide complete corrosion resistance.
- Corrugated stainless steel with corrosion resistant coating.
- 1/4 in. I.D. (3/8 in. O.D.).
- Connectors and fittings can be used with natural gas, LP gas (propane) and LP gas-air mixtures.
- Use to install 4-burner gas ranges, cook-top, dryers and water heaters.
- Safety+Plus2 TEFV valve helps protect against fires and explosions.
- Valve has no parts that can break or misalign over time for 24/7 protection.
- Connector and valve are 100% leak tested.
- No special tools required for installation.
- ProCoat coating corrosion resistant to most household chemicals, UV rays and salt.
- Approved for indoor and outdoor use.
- Temperature rating: -20°F to 150°F.
- Pressure rating: 1/2 psi maximum.
- ANSI Z21.24-2015/CSA 6.10-2015 and ANSI Z21.75-2016/CSA 6.27-2016, ANSI Z21.93-17/CSA 6.30-17.
- Designed, machined and assembled in the USA.
Every item checked for quality -
SharkBite 1/2 in. Brass Push-to-Connect Dishwasher Installation Kit
$36.36 $20.00The SharkBite Dishwasher Installation Kit has everything you need to install your new dishwasher, it’s fast and simple. Push-to-Connect fittings require no glue, soldering, unions or tools. The kit includes 1 SharkBite 1/2 in. Dual Outlet Angle Stop Valve, 1 SharkBite 1/4 in. x 3/4 in. MPT Elbow, 1 SharkBite 1/4 in. x 3/4 in. GHT Elbow, 1 SharkBite 1/4 in. Stop Valve Adapter, 10 ft. coil of 1/4 in. PEX Pipe, 2 Disconnect Clips (1/2 in. and 1/4 in.). The SharkBite Dual Outlet Angle Stop Valves work with copper, PEX or CPVC. Just insert the pipe and the stainless steel teeth bite down and grip tight, while a specially formulated O-ring compresses to create a perfect seal. Disassembly is just as fast using the simple disconnect tool so fittings and valves can be easily changed and reused. They can even be rotated after assembly for easier installation in tight spaces. The included PEX coils can be cut to the exact length needed so there is no excess supply line to coil up behind the dishwasher.
- Lead free DZR brass construction for durability and reliability.
- Use to connect to any combination of copper, PEX, CPVC or PE-RT pipes.
- Innovative push-to-connect design makes for quick and easy installation.
- Push-to-connect fittings require no solder, glue, unions, or tools.
- Fitting can be rotated on pipe after installation making it easier to work in tight spaces.
- Designed for potable water distribution as well as hydronic heating applications.
- Corrosion resistant to improve longevity.
- Certified as a manufactured joint and for underground and behind-the-wall applications without access panels.
- Meets all UPC, IPC and cUPC requirements.
- Demount clip allows user to release the fitting from the pipe for convenient installation flexibility.
- Rated to 200°F and 200 psi.
- Rated to 200°F and 200 psi.
Every item checked for quality -
Apollo 1/2 in. x 1/2 in. CPVC CTS Slip Stainless Steel MPT Adapter
$6.58 $3.62The Apollo 1/2 in. CPVC x Male Threaded Transition Adapter is simple to install and is designed for transitioning from CPVC to alternative piping systems. It is designed for use within hot and cold water pressure piping systems in all commercial and residential applications. The CPVC x Male Threaded Transition Adapter features a female solvent weld socket and a male threaded stainless steel connection. The fitting is used in applications where a change in the piping material is necessary.
- Compatible with CPVC pipe.
- Solvent weld slip x stainless steel male pipe thread (MPT) connection.
- Not compatible with gases or compressed air.
- Used to transition from CPVC piping system to alternative piping systems.
- NSF Listed.
- Meets UPC, IPC and cUPC standard.
Every item checked for quality -
#26, BrassCraft 1/2 in. Compression Inlet x 3/8 in. Compression Outlet Straight Valve
$5.45 $3.00
BrassCraft 1/2 in. Nominal Compression Inlet x 3/8 in. O.D. Compression Outlet 1/4 in. Turn Straight Valve controls water flow to household plumbing fixtures – faucets, toilets, dishwashers, icemakers, washing machines, etc. The straight valve is most often used where the water pipe enters the room from the floor. With a 90° turn of the valve handle, you are able to stop the flow of water leading to the plumbing fixture, allowing for maintenance and repair without shutting off the water to the entire home.
- Compatible with copper or PEX (PEX installations require a stainless steel tube insert).
- Smooth, quarter-turn operation, ON/OFF flow control with a 90° turn of the handle.
- 1-piece shut-off mechanism ensures smooth operation without freeze-ups even after long periods without use.
- Easy-to-remove handle protects against accidental operation during rough-ins.
- 1-piece body construction for strength, durability and long-lasting performance.
- Chrome-plated brass.
- Temperature rating: 40°F to 160°F.
- Pressure rating: 125 psi maximum.
- No-lead certified.
- IAPMO and CSA listed to ASME A112.18.1/CSA B125.1.
Every item checked for quality
